2jz – GTE toyota supra timing belt

2JZ – GTE TOYOTA SUPRA 2JZ -GTE timing belt replacement INSTALLATION1. INSTALL CRANKSHAFT TIMING PULLEY  2jz engine (a) Align the pulley set key with the key groove of the pulley.(b) Slide on the timing pulley facing the flange side inward. NOTICE:Do not scratch the sensor part of the crankshaft timing pulley.(c) Install the timing belt […]

2JZ – GTE TOYOTA SUPRA

2JZ -GTE timing belt replacement

INSTALLATION
1. INSTALL CRANKSHAFT TIMING PULLEY  2jz engine

(a) Align the pulley set key with the key groove of the pulley.
(b) Slide on the timing pulley facing the flange side inward.

NOTICE:
Do not scratch the sensor part of the crankshaft timing pulley.
(c) Install the timing belt plate with the bolt.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)

2. INSTALL IDLER PULLEY 2jz engine

(a) Apply adhesive to 2 or 3 threads of the pivot bolt.
Adhesive:
Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent
(b) Using a 10 mm hexagon wrench, install the plate washer and pulley with the pivot bolt.
Torque: 35 N·m (350 kgf·cm, 26 ft·lbf)
(c) Check that the pulley bracket moves smoothly.

3. TEMPORARILY INSTALL TIMING BELT

NOTICE:
The engine should be cold.
(a) Using the crankshaft pulley bolt, turn the crankshaft, and
align the timing marks on the crankshaft timing pulley and
on the oil pump body.
(b) Remove any oil or water on the crankshaft timing pulley
and idler pulley, and keep them clean.
(c) Install the timing belt on the crankshaft timing pulley and
idler pulley.
(When re-using timing belt): Align the match marks of the crankshaft timing pulley and timing belt, and install the belt with the arrow pointing in the direction of engine revolution.

4. INSTALL TIMING BELT GUIDE

Install the guide, facing the cup side outward.
5. INSTALL NO.1 TIMING BELT COVER
6. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the pulley,
and slide on the pulley.
(b) Using SST, install the bolt.
Torque: 324 N·m (3,300 kgf·cm, 239 ft·lbf)

7. CONNECT OIL COOLER TUBES

8. INSTALL CAMSHAFT TIMING PULLEYS
(a) Align the camshaft knock pin with the groove of the pulley,
and slide on the timing pulley.
(b) Temporarily install the timing pulley bolt.
(c) Using SST, tighten the pulley bolt.
Torque: 79 N·m (810 kgf·cm, 59 ft·lbf)

9. SET NO.1 CYLINDER TO TDC/COMPRESSION

(a) Turn the crankshaft pulley, and align its groove with timing
mark ”0” of the No.1 timing belt cover.
NOTICE:
Always turn the crankshaft clockwise.
(b) Using SST, align the timing marks of the camshaft timing
pulleys and No.4 timing belt cover.
SST 09960-10010 (09962-01000, 09963-01000)

10. INSTALL TIMING BELT

(When re-using timing belt):
Align the matchmarks of the timing belt and camshaft timing
pulleys.
(a) Remove any oil or water on the camshaft timing pulley,
and keep it clean.
(b) Install the timing belt, checking the tension between the
crankshaft timing pulley and exhaust camshaft timing
pulley.

11. SET TIMING BELT TENSIONER

(a) Using a press, slowly press in the push rod using 981 –
9,807 N (100 – 1,000 kgf, 220 – 2,205 lbf) of force.
(b) Align the holes of the push rod and housing, pass a 1.5
mm hexagon wrench through the holes to keep the push
rod retracted.
(c) Release the press.
(d) Install the dust boot onto the tensioner.

12. INSTALL TIMING BELT TENSIONER

(a) Temporarily install the tensioner with the 2 bolts.
(b) Alternately tighten the 2 bolts.
Torque: 26 N·m (270 kgf·cm, 20 ft·lbf)
P02587
(c) Remove the 1.5 mm hexagon wrench from the tensioner.

13. CHECK VALVE TIMING

(a) Slowly turn the crankshaft pulley 2 revolutions from TDC
to TDC.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that each pulley aligns with the timing marks as
shown in the illustration.
If the marks do not align, remove the timing belt and reinstall it.

14. INSTALL DRIVE BELT TENSIONER

Install the tensioner with the 3 bolts.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
NOTICE:
Be careful not to drop the bolts inside the timing belt cover.

15. INSTALL NO.2 TIMING BELT COVER

16. INSTALL NO.3 TIMING BELT COVER

17. INSTALL PS PUMP
(a) Temporarily install the pump pulley with the nut.
(b) Using SST, tighten the pulley nut.
Torque: 43 N·m (440 kgf·cm, 32 ft·lbf)
18. INSTALL WATER PUMP PULLEY, FAN, FLUID
COUPLING ASSEMBLY AND DRIVE BELT
(See page CO-1 1)

19. INSTALL DRIVE BELT TENSIONER DAMPER

Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
20. INSTALL RADIATOR ASSEMBLY

21. ROAD TEST

Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.

2JZ - GTE TOYOTA SUPRA

2JZ - GTE TOYOTA SUPRA

2JZ - GTE TOYOTA SUPRA

2JZ - GTE TOYOTA SUPRA

2JZ - GTE TOYOTA SUPRA timing belt

2JZ - GTE TOYOTA SUPRA timing belt

2JZ - GTE TOYOTA SUPRA timing belt


Home

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Scroll to Top